Exactly How To Install A Bath Tub (For Novices).
Exactly How To Install A Bath Tub (For Novices).
Blog Article
Just about everyone has got their own conception about How to Install a Bathtub Yourself.
Setting up a bathtub isn't specifically rocket science, yet it does need strong plumbing, carpentry, and also often, tiling skills. Changing an old bathtub with a brand-new one is also a reasonably challenging task. If the old bathtub is readily easily accessible, the project can relocate quickly; if you need to open a wall surface to remove the old bathtub and place the new tub, the task is a lot harder. In either case, the job is within a home handyman's abilities, although you will certainly need a helper to vacate the old bathtub and embeded in the new one. See to it you have certified yourself for the work as well as fit trying it. Rather than employing a contractor to take over a halfway-completed task, it is much better to consider utilizing one prior to you begin. Opportunities are you may require a professional plumber to make tube links.
This write-up will assist you mount a new tub in your washroom if you have already acquired a new tub and also do not require to change the arrangement of your previous water supply pipes.
Your tools and material checklist ought to comprise the following:
Planning for the Installment
First of all, the sustaining framework supplied with the bath ought to be fitted (if required) according to the producer's instructions. Next, fit the taps or mixer to the bathtub. When suitable the faucet block, it is very important to make certain that if the tap includes a plastic washer, it is fitted between the bathroom and also the faucets. On a plastic bathroom, it is also sensible to fit a supporting plate under the faucets device to avoid strain on the bathtub.
Fit the adaptable faucet ports to the bottom of the two taps making use of 2 nuts and also olives (sometimes supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet through the hole in the bath. Use the nut provided by the supplier to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bath. Make sure you utilize every one of the supplied washers.
Attach the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Connect all-time low of the overflow tube in a comparable manner.The bath should currently prepare to be fitted in its final placement.
Removing Old Touches
If you need to replace old faucets with brand-new ones as a part of your setup, then the first thing you need to do is detach the supply of water. After doing so, activate the taps to drain pipes any kind of water staying in the system. The process of getting rid of the existing faucets can be quite bothersome because of the restricted accessibility that is typically the case.
Make use of a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipelines to the taps. Have a cloth all set for the continuing to be water that will come from the pipelines. When the supply pipes have actually been removed, make use of the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the single faucets from turning throughout this process. When the taps have actually been removed, the holes in the bath/basin will certainly need to be cleaned up of any kind of old sealing substance.
Prior to proceeding to fit the brand-new taps, compare the pipeline links on the old taps to the new taps. If the old faucets are longer than the new taps, after that a shank adapter is needed for the new taps to fit.
Setting up the Tub
Making use of the two wood boards under its feet, place the tub in the called for position. The wooden boards are handy in evenly spreading out the weight of the bath tub over the area of the boards rather than concentrating all the weight onto four little factors.
The following goal is to make certain that the bathtub is leveled all round. This can be attained by inspecting the level as well as readjusting the feet on the tub till the spirit level reviews level.
To mount taps, fit all-time low of the furthest adaptable tap adapter to the appropriate supply pipe by making a compression sign up with; then do the very same for the other faucet.
Activate the supply of water and also inspect all joints and also new pipework for leakages and tighten them if needed. Load the tub as well as also inspect the overflow electrical outlet as well as the regular outlet for leaks.
Ultimately, fix the bathroom paneling as explained in the supplier's instruction manual. Tiling as well as securing around the bathtub must wait till the bathtub has actually been used a minimum of when as this will settle it right into its last position.
Fitting New Touches
If the tails of the new taps are plastic, after that you will certainly require a plastic connector to prevent damage to the thread. One end of the port fits on the plastic tail of the faucet and also the other end provides a connection to the existing supply pipelines.
If you require to fit a monobloc, after that you will certainly call for reducing couplers, which connects the 10mm pipe of the monobloc to the conventional 15mm supply pipeline.
Next off, place the faucet in the placing opening in the bath/basin ensuring that the washers are in place between the tap and also the sink. Safeguard the faucet in position with the manufacturer offered backnut. When the faucet is firmly in position, the supply pipelines can be connected to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with regular faucet adapters. The previous type should be connected to the tap ends initially, tightening up just by hand. The supply pipes can later be connected to the other end. Tighten both ends with a spanner after both ends have been linked.
Tiling Around the Tub
In the area where the bath satisfies the ceramic tile, it is needed to seal the joins with a silicone rubber caulking. This is very important as the installation can relocate sufficient to break a stiff seal, triggering the water to permeate the wall between the bath and the tiling, leading to problems with dampness and possible leaks to the ceiling listed below.
You can pick from a selection of coloured sealers to assimilate your fixtures and fittings. They are sold in tubes and also cartridges, and also can securing spaces as much as a width of 3mm (1/8 inch). If you have a larger void to fill up, you can fill it with twists of drenched paper or soft rope. Remember to always load the tub with water before securing, to enable the motion experienced when the tub remains in usage. The sealant can fracture rather early if you do not take into account this activity before sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are likewise easily offered on the market. It is advisable to fit the ceramic tiles using waterproof or waterproof glue as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I came across that article about How to Install a Bathtub Yourself while browsing the search engines. Sharing is nice. You never know, you might be helping someone out. I love reading our article about Tools You Need to Install a New Bathtub .
Schedule A Service Report this page